Verified NCM-MCI-5.20 dumps Q&As - 100% Pass from Prep4away
Pass NCM-MCI-5.20 Exam in First Attempt Guaranteed 2023 Dumps!
NEW QUESTION # 53
An administrator inherits a new Nutanix environment and logs in to a CVM to check the network configuration. The configuration is as follows:
Which action should the administrator take to improve network performance?
- A. Configure VLAN tagging both on br0 and br1 and their physical interfaces.
- B. Configure balance-sib or balance-tcp mode for br0-up if switch configuration allows
- C. Add eth0 and eth1 to the br0-up bond
- D. Remove one 10 Gbs interface from br0-up to make sure all 10 Gbs can be used.
Answer: B
NEW QUESTION # 54
An alert about RX errors on eth2 on a node is reported in the cluster. The administrator logs in to the CVM in question, checks the ping_* files in the data/logs/syststats folder, and notices intermittent ping loss.
The node in question has the following network configuration:
Which action should be used to troubleshoot without disrupting the VMs running on this node?
- A. Remove eth3 from br0-up and monitor for new alerts
- B. Replace the cable from eth2 to the switch
- C. Check the port on the switch side for any errors
- D. Enable balance-s1b on br0-up and monitor if a problem persists
Answer: C
NEW QUESTION # 55
An administrator needs to evaluate if the existing configuration of Protection Domains meets the specified corporate recovery policy for SQL Dat a. The corporate policy requires that all SQL Servers be recoverable at the DR site within 30 minutes, and must result in a maximum of 60 minutes of data loss. SQL data must be required.
The protection domain is configured as follows:
* Application consistent snapshots are enabled
* The SQL server VMs are assigned to the Protection Domain as their own Consistency Group
* The Protection Domain schedule is configured as snapshots taken every 90 minutes from 7 am until 8 pm What must be changed to meet the required policy?
- A. Revise the schedule tc be 15 minutes
- B. Revise the schedule to be 60 minutes
- C. Revise the schedule to be 30 minutes
- D. Revise the schedule to be 45 minutes
Answer: B
NEW QUESTION # 56
Refer to the exhibit.
An administrator notices a critical alert on the Metro Availability Protection Domain What is causing this alert?
- A. VMware Site Recovery Manager is handling a failover event
- B. Metro Availability did not fail over and caused an outage.
- C. Metro Availability Protection domain is active on the remote site.
- D. vSphere moved VMs to the remote container, and the VMs must be moved back.
Answer: C
NEW QUESTION # 57
An administrator is responsible for the following Nutanix Enterprise Cloud environment:
* A central datacenter with a 20-node cluster with 1.5PB of storage
* Five remote sites each with a 4-node cluster with 200TB storage
The remote sites are connected to the datacenter via 1GB links with an average latency of 6 ms RTT. What is the minimum RPO the administrator can achieve for this environment?
- A. 6 hours
- B. 1 hour
- C. 0 minutes
- D. 15 minutes
Answer: D
NEW QUESTION # 58
Refer to the exhibit.
After performing ESXi to AHV conversion on a cluster, the alerts shown in the exhibit display on Prism. What should the administrator do to resolve this issue efficiently?
- A. Delete the Protection Domain, create a new Protection Domain, and add the VMs to it
- B. Remove the VMs. create a new Protection Domain, and add VMs to it
- C. Create a new Protection Domain and add the VMs to rt.
- D. Remove VMs from the Protection Domain and add them back in.
Answer: D
NEW QUESTION # 59
An administrator needs to create and start five new VMs for a Data Analytics Project (OLAP). The VM Profile is as follows:
* vCPU:4
* vRAM: 64 GB
* vDisk: 1.5 TB
Each of the four nodes of the Nutanix cluster has the following:
* 24 vCPU. 20% overall usage
* 192 GB RAM, 60% overall usage
* 2xl920GBSSD
* 4x 2 TB HDD
At cluster level, there is a single RF2 container that is 30% utilized and has an extent store capacity of 13.5 TB.
Which component requires administrator attention?
- A. Storage, because the capacity is not enough to create VMs.
- B. Physical RAM, because it is not enough to power on all of the new VMs.
- C. Physical Cores, because they are not enough to power on all of the new VMs.
- D. Flash Tier because it is not enough to accommodate the workloads.
Answer: B
NEW QUESTION # 60
When Does AOS automatically Generate a case with nutanix Support?
- A. For every alert detected by pulse Diagnostics
- B. When disk space usage is high above 90%
- C. When losing network connectivity to the CVM
- D. On failure of a scheduled NCC check
Answer: D
NEW QUESTION # 61
An administrator receives a notification that storage in a Nutanix cluster is unavailable. The cluster consists of five nodes and is configured with a Fault-Tolerance level of 1 (FT-1).
Upon investigation, the administrator finds the following:
* All AHV hosts are powered on and the CVMs are running
* Nodes A, B, and C are connected to one top of rack switch
* Nodes D and E are connected to a second top of rack switch
* The cluster status command run on Node A shows that CVM services on nodes D and E are down Which issue is causing the storage outage?
- A. The genesis process is down on both Nodes D and E.
- B. The switch connecting Nodes D and E is down.
- C. The default gateway for the CVMs and AHV hosts is down.
- D. Nodes D and E are in maintenance mode.
Answer: B
Explanation:
https://hyperhci.com/2020/07/29/nutanix-cluster-services-down-troubleshooting/
NEW QUESTION # 62
An administrator needs to initiate a new VDI project within a couple of months. Prism Central reports there are no storage resources to accommodate such workloads.
The administrator sees many powered-off VMs and has the authority to delete test VMs powered off at least for 30 days. Test VMs belong to the Test category.
Using Prism Central, which steps are required to identify the correct VMs to be deleted?
- A. Create a new Scenario selecting Test VMs. filter by uptime
- B. Use Capacity Runway to filter by Test and Powered-off VMs
- C. Filter VMs list, choose Test category and Inactive under Efficiency
- D. Create a new Project selecting Test VMs, sorting by power state
Answer: C
Explanation:
NEW QUESTION # 63
An administrator finds that home shares cannot be configured in a new Files 3.5 deployment. Why is this happening?
- A. NFS default access is set to Read Only.
- B. Access Based Enumeration is not enabled.
- C. Multi-protocol access is not configured.
- D. The system is deployed as a single FSVM.
Answer: D
NEW QUESTION # 64
A systems administrator needs to add more VMs to their Nutanix cluster.
Which two actions should the administrator perform to determine if the current cluster can accommodate the new VMs? (Choose two.)
- A. Perform an Inventory with Life Cycle Management.
- B. Utilize Optimize Resources for VM efficiency.
- C. Enable Deduplication and Erasure Coding.
- D. Determine utilization with Cluster Runway.
Answer: B,D
Explanation:
Reference:
NEW QUESTION # 65
An administrator is deploying an application using Nutanix Volumes. After configuring the volume group and connecting the guest's iSCSI initiator to the volume group, they begin performance testing.
The administrator learns that performance on the virtual disk attached to the iSCSI initiator is far less than that of a virtual disk connected directly to the VM.
Which situation is causing this condition?
- A. The VM's iSCSI traffic is being routed to the data services IP subnet
- B. The duster data services IP address is a bottleneck, shared with other iSCSI traffic
- C. The performance test is generating small block random 10.
- D. Data Locality ensures that VM attached disks are always faster than iSCSI volumes.
Answer: B
NEW QUESTION # 66
An administrator receives reports that VDI desktop performance in an 8-node Nutanix VDI environment is poor. Opening applications takes between 1 and 2 minutes.
When investigating the issue, the following conditions are found:
* Cluster memory utilization: 80%
* Cluster SSD utilization: 70%
* Average VM CPU Wait Time: 11%
* CVM CPU utilization: 75%
Which action should be taken to improve VDI performance?
- A. Increase the number of vCPU cores allocated to the CVM.
- B. Add CPU resources to the cluster.
- C. Increase the amount of SSD storage in the cluster.
- D. Add memory to the nodes in the cluster.
Answer: B
NEW QUESTION # 67
A Nutanix cluster is deployed with the following configuration:
* Three four-node blocks (A, B, and C)
* All Flash Redundancy Factor 2
What is the effect of simultaneous disk failures on two nodes located in block A?
- A. VMs are migrated off of the nodes with disk failures.
- B. Each node with a failed disk is marked as degraded.
- C. VM read and write operations continue normally.
- D. VMs on the nodes with failed disks are unable to write data
Answer: C
NEW QUESTION # 68
An administrator receives an alert in Prism indicating that interface eth2, on an AHV host is receiving many CRC errors. After togging into the problematic host, the following command is run to show the indicated output:
What is causing this issue?
- A. Incorrect link speeds on the switch
- B. A physical layer network problem
- C. A misconfigured bond
- D. The interface is incorrectly configured with Jumbo Frames
Answer: D
Explanation:
Reference:
rx_crc_errors are caused either by faults in layer 1 (in the past, we have seen failed twinax cables and incorrect types of fibre being used), or issues with jumbo frames on the network. In an environment with 10 Gig switches that use cut-through forwarding (Cisco Nexus, Arista, Cisco devices using IOS default to Store and Forward switching), any packets that come into the switch will get forwarded out the destination interface once the switch has read the destination MAC address. If that packet has an MTU over what is configured on the interface, it will cut off the packet at the designated MTU, causing the server to receive a malformed packet, which will throw a CRC error.
If you have a layer 1 issue, you will see rx_crc_errors, not on all but one or two nodes.
NEW QUESTION # 69
An administrator recently installed Prism Central to use categories, after having created categories and values, the administrator needs to apply these categories to multiple workloads.
How can the administrator easily perform this task?
- A. Create a Playbook to automate the process
- B. Go to Categories and select the VMs to be added
- C. Manage the VMs ownership
- D. Choose multiple VMs and select Manage Categories
Answer: D
NEW QUESTION # 70
Which command should an administrator run from the CLI to view the uplink state of all AHV nodes in the cluster?
- A. manage ovs show uplinks
- B. allssh manage_ovs show_uplinks
- C. manage_ovs show_uplinks
- D. allssh show_uplinks
Answer: B
NEW QUESTION # 71
A new Nutanix cluster is ready for production on a remote site with no IT staff. Changes to the infrastructure will cost money and probably cause a cluster stop. The administrator needs to perform a health check on the environment that should include:
* Network connectivity checks
* Network performance status
* Storage performance status
Which tool should be used to perform this test?
- A. X-Ray
- B. NCC
- C. clurator_cli
- D. diagnostic, py
Answer: B
NEW QUESTION # 72
An administrator is deploying a new application to a Nutanix Enterprise Cloud. The application requires a security to prevent unauthorized access. The application also uses many non-standard ports that are unique to it. Security should not be changed for existing applications.
What should the administrator do to meet these requirement?
- A. Use existing categories for the VMs and modify existing security policies to include the specific port.
- B. Use existing categories for the VMs. and create new security policies to use the existing categories.
- C. Create new categories for the VMs, and modify existing security policies to include the new categories.
- D. Create new categories for the VMs, and create new security policies that include the new categories.
Answer: D
NEW QUESTION # 73
Refer to the exhibit.
An administrator configures Active Directory authentication as shown in the exhibit. Upon finishing setup, users are not able to log in.
What configuration change should be made to fix this issue?
- A. Change leaps to https
- B. Change the Directory URL to use an IP rather than a name
- C. Change the plct from 389 to 636
Answer: C
Explanation:
D Change the Domain to use an IP rather than a name
NEW QUESTION # 74
Refer to the exhibit.
User 1 and User 2 belong to the AAPM group
What are two descriptions of how Files perform quota management? (Choose two.)
- A. User 2 can add an 8GB file without receiving a notification email.
- B. User 2 can continue to add another 3GB file but will receive a daily notification email.
- C. User 1 can add an 8GB file to the share without receiving notification.
- D. User 1 can continue to add another 5GB file but will receive a daily notification email.
Answer: A,D
NEW QUESTION # 75
An administrator receives reports about a Nutanix environment. The investigation finds the following;
* VMs are experiencing very high latency
* Each node is equipped with a single SSD, utilized at 95%
* Each node is equipped with three HDDs, utilized at 40%
Why are the guest VMs experiencing high latency?
- A. All VM write operations are going to HDD.
- B. All VM read operations are coming from HDD.
- C. CVMs are overwhelmed by disk balancing operations.
- D. VMs are unable to perform write operations.
Answer: B
NEW QUESTION # 76
An administrator is unable to discover a Nutanix-hosted iSCSI Block device allocated to a bare-metal host.
What is causing this issue?
- A. Network segmentation has not been enabled
- B. External Host IP address is not in FileSystem Whitelist
- C. External client access has not been enabled for the host
- D. Jumbo Frames has not been configured on the switch
Answer: B
NEW QUESTION # 77
......
The Nutanix NCM-MCI-5.20 exam covers various topics related to multicloud infrastructure, including cloud management, network virtualization, storage virtualization, and server virtualization. The exam is designed to assess the candidate's understanding of multicloud infrastructure and their ability to apply their knowledge to real-world scenarios. The certification is suitable for professionals who work with multicloud infrastructure, including cloud architects, infrastructure engineers, and system administrators.
NCM-MCI-5.20 Dumps Full Questions - Exam Study Guide: https://actualtests.prep4away.com/Nutanix-certification/braindumps.NCM-MCI-5.20.ete.file.html